Alexander Rostokin

Under-cabinet lighting: types and placement tips

Under-cabinet lighting gives the benchtop a usable layer of light without relying on a bright ceiling fitting. It helps with chopping, washing dishes and finding the right saucepan after dark, while making the worktop appear cleaner and more inviting. The best system is planned around the work zones in the room, rather than installed as one continuous strip in every cabinet.

Australian kitchens make that planning worthwhile. Many suburban homes have open-plan living areas, a large central benchtop and cabinet runs that continue past the cooktop, while fibro bikkies and older brick-veneer houses often come with narrow rooms and awkward service spaces. A compact apartment may need a very different solution from a family kitchen with a sink, pantry coffee station and breakfast bar. An Aussie “reno” can look polished with lighting that follows each task rather than flooding everything evenly.

Mains power in Australia is 230 volts, and hardwired fittings or new circuits should be arranged through a licensed electrician who can supply the relevant RCM documentation for the job. Plug-in fittings can offer a simpler route in suitable locations. Because summers can be hot and coastal homes can be damp, low-heat LED equipment, ventilated drivers and suitable moisture ratings are sensible choices rather than optional extras.

Plan around the work, not the whole room

Start by marking the tasks that happen after sunset: preparing food at the main benchtop, cleaning at the sink, filling the kettle and grabbing items from the pantry. These zones can be switched separately, which is often more useful than dimming one long run. Leave the area directly over a cooktop less dependent on concealed strip lighting, as rising heat and grease can shorten the life of drivers and adhesives.

Check the cabinet fronts before choosing a fitting. A flat slab, a framed door, a drawer bank and a recessed shelf each change how far light spreads. Deep drawers, upright pantry cabinets and glass-fronted doors may need their own zones. Measure the clear space under each cabinet and note handles, rails and plinths; they can cast hard shadows or catch the beam if the strip is mounted in the wrong line.

Choose strips, profiles, bars or pucks

Flexible LED strip is the most flexible option for a continuous run. Most DIY-friendly systems use 12 or 24 volt LED strip with a separate transformer or driver, while ready-to-connect kits may include both. The strip can follow cabinet corners when it is sold by the metre, but it should only be cut at marked points. An aluminium profile gives the strip a rigid channel, helps dissipate heat and can carry a diffuser for a softer beam.

Rigid LED bars are simpler to align and often come with an integrated diffuser and lead. Puck lights suit a short cabinet or pantry and are quick to install, but separate pools of light can look patchy over a long benchtop. Older halogen or fluorescent fittings may still be present in an Australian kitchen, yet replacements generally use less energy and run cooler. Choose the fitting type according to the cabinet shape, available wiring space and the evenness of coverage required.

Get the light quality right

Under-cabinet light is judged at the benchtop, so colour temperature and colour rendering matter more than raw brightness. Around 2700 to 3000 kelvin gives a warm finish that many homeowners prefer with timber cabinets and warm white splashbacks; 3500 to 4000 kelvin suits a crisp, task-oriented look. A high colour-rendering index, ideally 90 or above, makes food and timber colours appear more natural.

Controls should suit the way the room is used. A dimmer on a separate circuit can provide softer evening light, while a local switch at the pantry is handy when nobody wants to enter a dark main kitchen. Motion sensors can suit a less-used appliance garage, but they are less valuable where the strip stays on while someone chops for several minutes. Any dimmer, driver and strip must be rated as a compatible set; mixing protocols can cause flicker.

Map the power before measuring lengths

Map the electrical route before buying lengths. Decide which cabinets are hardwired and which can use a plug-in supply, then check where a driver can sit without being buried in a hot, sealed void. A qualified electrician should size the circuit and protective devices for the total load, especially if several high-output runs share one circuit. In a rental or strata-managed apartment, the owners’ consent and building electrician may also be required.

Type I plugs and 230-volt outlets make plug-in strips practical in pantries and appliance garages, provided the lead is secured and kept clear of water. A new 230-volt installation, switched circuit or alteration belongs with a licensed electrician under the relevant state rules and Australian wiring standards. Ask the electrician to position outlets, drivers and switches so they can be serviced without dismantling a cabinet or benchtop.

Prepare the cabinet and mount the fittings

Before mounting a strip or profile, clean the underside with the alcohol wipe recommended by the manufacturer and allow it to dry. Measure twice, mark both ends and check that the cable can reach the driver without being stretched through a hinge. Adhesive-backed strip can be used on a smooth, clean surface, but purpose-made clips or screws are better where vibration, heat or frequent handling is likely.

Profiles must be cut with a fine saw and squared so the LED strip sits flat against the aluminium. Connect the marked power and return sections in the correct polarity, and never splice in the middle of an uncut run. Fit the diffuser only after the strip has been positioned and tested. Near a sink or in a damp pantry, select an appropriate ingress-protection rating and keep indoor drivers in a dry, ventilated place; a sealed strip can still fail because its concealed supply is overheated.

Position the light for even coverage

For a typical 600-millimetre-deep cabinet, place the strip in the rear half of the underside, roughly 50 to 100 millimetres from the backsplash and at least 150 millimetres from the front edge. This position will often wash both the worktop and splashback. It can create stronger shadows behind upright objects, so move it toward the front if a kettle or chopping board blocks the main working area. Always follow the fitting’s beam angle and mounting instructions.

Think in straight, uninterrupted runs, but split them at walls, tall units or cabinet changes that interrupt the light. Under a sink, mount the fitting to the side or front rail where moisture is less likely. A window above a sink can cause reflections at night; offsetting the strip or using a lower-output, wider diffuser may reduce glare. For dark, glossy stone or a mirrored splashback, diffuse the source and test it from several seats before fixing it permanently.

Connect, test and maintain the system

Once installed, energise the circuit and check every zone from a seated position and from each normal standing position. Look for dark patches at joints, sharp reflections on the benchtop and flicker when the light is dimmed. Adjust the profile or diffuser rather than increasing the output, because excess brightness makes the eye adapt poorly to the rest of the kitchen.

Routine care is light: wipe the diffuser and splashback with a soft damp cloth, keeping liquid away from the driver and connectors. If a section fails, check the driver and connections before replacing the LED tape, and use a replacement with the same voltage, wattage and colour temperature. A well-planned installation gives Australian kitchens dependable task light while keeping the ceiling calm and the benchtop clear.